Built to Australian Standards

Tiling & Waterproofing
Services

Waterproofing, tiling, screeding, and outdoor paving delivered with compliant systems, clean finishes, and reliable certified contractors. Fully insured.

Certified in waterproofing & tiling
Public liability & WorkCover insured
Clear quoting + disciplined delivery

FAQ

Bathroom waterproofing by Vworth Tiling and Waterproofing

Explore Services

Waterproofing & Sub-Prep

Precision Tiling

Grout & Tiling Repair

Waterproofing

built right before tiles go down

Waterproofing & Substrate Preparation

Completed in accordance with NCC requirements and relevant Australian Standards, including AS 3740 , AS 3958.1, AS 4654.2 (where applicable).
Scope and system selection depend on design, substrate condition, wet-area type, and manufacturer requirements.

Screeding

Waterproofing

Substrate Preparation

Screed and levelling works carried out to correct levels where required and create a consistent surface suitable for waterproofing and tile installation.

Screed Types ( where applicable)

Unbonded screed
Sand & cement screed
Self-levelling compound (liquid screed)

Scope

Screed work to correct levels where required
Falls preparation for wet areas (when applicable)
Surface levelling for tile installation
Substrate made consistent for finish quality

Typical Work

Floor levelling / correction
Screed to suit tile format and substrate
Preparation prior to waterproofing (wet areas)

Notes:

Screed method, thickness, and material selection depend on existing levels, substrate condition, and required finish. Falls preparation applies to wet areas where required and achievable within project constraints and manufacturer requirements.

Internal and external waterproofing systems installed in accordance with NCC requirements, relevant Australian Standards, and manufacturer system instructions prior to tiling or final finishes.

Services

Internal wet-area waterproofing (e.g. bathrooms, ensuites, laundries)
External waterproofing (balconies, terraces, podiums, planter boxes)
Membrane systems and compatible primers
Junctions, penetrations, and critical detailing
Preparation and waterproofing prior to tiling

Scope

Wet-area membrane systems (internal)
External membrane systems (where applicable)
Junctions, penetrations, and detailing
System installed in accordance with manufacturer requirements
Surface prepared and left ready for tiling or specified finish

Typical Work

Internal wet areas: bathrooms / ensuites / laundries
External areas: balconies / terraces (project dependent)
Renovation re-waterproofing (where applicable)
Critical detailing around penetrations, junctions, and terminations

Preparation works completed prior to screeding, waterproofing, and tiling. Method and materials are selected based on substrate condition, wet-area type (where applicable), and manufacturer system requirements.

Scope

Surface assessment and preparation
Removal/correction of defects where required
Priming to suit substrate condition and system requirements
Preparation to achieve a ready-to-install surface

Typical Work

Patch repairs and surface corrections
Substrate cleaning / preparation
Primers matched to membrane/adhesive system

Notes:
Scope is confirmed after assessment and is not limited to floor preparation only. Where required, additional preparation may be needed to walls, junctions, or surrounding components to achieve the best practical outcome and support the system requirements.

View related FAQs

Tiling

Substrate Preperation

tile installation

Precision Tiling

Tiling installed with consistent set-out, clean cuts, and crisp finishes. All projects installed to suit tile type, substrate condition, and the area (internal / wet / outdoor).

Floor Tiling

Wall Tiling

Outdoor Tiling & Paving

Kitchen Splashbacks & Feature Tiling

Flat, level floors with correct falls where required and durable finishes.

Scope

Set-out and levels (incl. fall checks where needed)
Correct adhesive selection (tile + substrate)
Movement joints where required
Consistent joints and clean edges
Grout finish + silicone junctions

Typical Work

Bathrooms & ensuites
Living areas / hallways
Renovation floors over existing substrates (as suitable)

Notes:

Substrate condition and levels are assessed before installation; preparation / levelling / fall may be required to achieve a compliant finish.

Controlled set-out and straight lines with clean edge finishing for walls and wet areas.

Scope

Set-out, centrelines, and layout planning
Cutting, scribing, and neat penetrations
Edge trims / mitres (where applicable)
Consistent joints and alignment
Silicone finishing to junctions

Typical Work

Bathrooms / laundries / powder rooms
Feature walls
Large-format wall tiles

Notes:

Final layout and cut positions are confirmed on site based on tile size, room geometry, and fixtures.

Outdoor tiling/paving installed with correct set-out, falls, and weather-ready detailing.

Scope

Set-out + fall management (where required)
Movement joints suited to outdoor exposure
Drainage-aware layout planning
Cutting, edging, and termination details
Weather-suitable adhesive, sealant and grout selection and preparations

Typical Work

Patio and outdoor living areas
Steps and landings
Pool surrounds
Balconies / terraces

Notes:

External installations depend on substrate condition, drainage requirements, and tile/paver suitability for outdoor use. Waterproofing (where required) is assessed and carried out as a separate scope under Waterproofing

Kitchen splashbacks and feature areas installed with clean set-out, tight cuts, and neat termination details.

Scope

Splashbacks and feature areas
Mitres / trims / edge detailing
Niches, shelves, and fixture cut-outs
Straight joint alignment and symmetry
Clean silicone finishing

Typical Work

Kitchen splashbacks
Feature strips / patterned layouts
Wet area walls
Laundry splash zones

Notes:

Pattern layouts depend on tile size, orientation, and selected feature alignment.

View related FAQs

Precision wall and floor tiling by VWORTH Tiling & Waterproofing

Grout

tile restoration

Grouting & Tile Repair

Regrouting, resealing, and targeted tile repairs to restore joints, improve hygiene, and address common wet-area leak points—without full tile removal (where suitable).

Assessment first → spot repair vs full regrout → clean finish + clear aftercare.

Tile Repair & Replacement

Silicone & Sealing

Regrouting Services

Localised repairs and tile replacement where tiles are cracked, loose, or damaged—paired with regrouting/resealing to blend with surrounding areas.

Scope

Assessment of cause (impact vs movement)
Removal and replacement of damaged tiles (where possible)
Regrout and reseal to blend with surrounding area
Localised repairs (where suitable)

Typical Work

Cracked tiles and drummy/loose tiles
Tiles cracked from movement / impact
Repairs after plumbing access works
Small-area replacements in renovations

Notes:

Matching depends on tile availability and batch differences. If substrate movement is present, preparation may be required for a lasting repair.

Removal and replacement of failed silicone at junctions to restore clean edges and reduce water entry at perimeter joints.

Scope

Removal of failed silicone + proper surface preparation
Re-sealing wall/floor junctions and perimeters
Neat finishing around fixtures and screens
Colour selection matched to surrounding finishes

Typical Work

Shower perimeter joints and corners
Vanity/bench edges and wet-area junctions
Mouldy or split silicone replacement

Notes:

Silicone replacement improves perimeter sealing but does not replace waterproof membranes behind the tile system where those have failed.

Removal and replacement of failed grout to restore joint integrity, appearance, and water resistance in wet areas (where suitable).

Scope

Inspection + recommendation (spot repair vs full regrout)
Removal of failed grout +joint preparation
Regrouting to suit tile type and joint width
Sealing

Typical Work

Cracked / missing / discoloured grout joints
Mould-affected grout and failed wet-area joints
Shower floors and wall/floor junctions

Notes:

Results depend on underlying movement and what’s happening behind the tiles. If joints are failing due to movement or system issues beyond the grout, additional repair work may be required.

View related FAQs

Our Process

1. Visualise The Vision

We listen, confirm the goal, and map the project with clarity.

3. Mark-ups

We review layouts, levels, and key details before work begins.

5. Commence

We execute with discipline and clean site standards.

2. Schedule

We align timelines and plan the workflow so the job runs efficiently.

4. Agreement

Scope, materials, and access are confirmed — no surprises.

6. Completion & Care

We clean, inspect, and hand over with clear aftercare and bonuses.

About VWORTH

Built on discipline, clean finishes, and clear communication.

Meet the team behind V.Worth,

How we plan, protect, and finish properly.

Built to Australian standards — no shortcuts.

Our Story & Standards

V.Worth's Values

Our Service Area

Serving Melbourne Metro and surrounding suburbs (based in Mount Waverley).

Outer areas by request.

Quick Links

FAQ

7 - Steps Quick Quote

Our Values

Request a Call Back

09:00 AM

Cheers Mate, Let's talk soon !

Tiling & Waterproofing Services

Explore Services

Waterproofing & Substrate Preparation

Completed in accordance with NCC requirements and relevant Australian Standards, including AS 3740 , AS 3958.1, AS 4654.2 (where applicable). Scope and system selection depend on design, substrate condition, wet-area type, and manufacturer requirements.

Screeding

Waterproofing

Substrate Preparation

Screed Types ( where applicable)

Scope

Typical Work

Substrate Preperation

Precision Tiling

Tiling installed with consistent set-out, clean cuts, and crisp finishes. All projects installed to suit tile type, substrate condition, and the area (internal / wet / outdoor).

Floor Tiling

Wall Tiling

Outdoor Tiling & Paving

Kitchen Splashbacks & Feature Tiling

Scope

Typical Work

Grouting & Tile Repair

Tile Repair & Replacement

Silicone & Sealing

Regrouting Services

Scope

Typical Work

Our Process

About VWORTH

Our Service Area

Quick Links​

Services

Contact Details

Email Us

Call Us

Working Hours

Request a Call Back

It’s about you — not us.

Tiling & Waterproofing
Services

Completed in accordance with NCC requirements and relevant Australian Standards, including AS 3740 , AS 3958.1, AS 4654.2 (where applicable).
Scope and system selection depend on design, substrate condition, wet-area type, and manufacturer requirements.

Quick Links